CBC ZR-DH1621NP Installationsanleitung

T-Command Building Block Video Ltd., 17 Apex Park, Diplocks Industrial Estate, Hailsham, East Sussex, BN27 3JU UK. Tel: +44(0)1323 842727 Fax: +44

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 10 8. Tx1500 In this Keypad Type you will be able to control the BBV Tx

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 11 If you press MENU you will move on to the next screen this gives more

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 12 9. DX1 DIXONS In this Keypad Type you will be able to control the BBV

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 13 Within the DX1 there is an Engineering Menu, to access this menu you

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 14 To navigate the menu you will need to use the joystick tilt up & d

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 15 10 Ganz DVR Notes on using Touch Screen Keypad (V9 software) with GANZ

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 16 PTZ Screen. This screen is displayed after pressing the PTZ key. The

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC 11 Ganz DVR CONNECTION INFORMATION Fig. 6 interconnecting cable between T-Co

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC 12 FAST DVR Connection between T-Command (keyboard port) and FAST DVR C

CHANGING CAMERA Press the CAMERA pad then using the numeric pads to select the camera required and then press the ENTER pad to select this new

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 2 1. PRE-INSTALLATION CHECKS AND SAFETY PROCEDURES UNPACKING Check Packa

Other BBV products. Product Description TX300 Single camera desktop telemetry transmitter with BBV up-the-coax & 20mA telemetry, Pan/Tilt/L

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 3 Damage Requiring Service - Servicing by qualified personnel should be c

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 4 2. INTRODUCTION GENERAL The T-Command is designed to allow c

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 5 3. INSTALLATION OPERATING VOLTAGE The T-Command requires 9VDC @ 50

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 6 Fig. 2 Rear view of the T-Command Keypad. 4. DATA CONNECTIONS The T-

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 7 Fig. 4 Internal view of the T-Command keypad. RS232RS422/485RS232RS42

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 8 5. POWER UP SCREEN When the T-Command is powered up you will

TCOMMAND OPERATING INSTRUCTIONS V1.3 09-03-2009 V18 SOFTWARE.DOC Page 9 7. ENGINEERING MENU The Engineering Menu allows you to do a number o